Please select To the mobile version | Continue to access the desktop computer version
| |

Kaosun's CD Players

 Forgot password?
 Repair!
Search
View: 766|Reply: 5

SONY discman D-5 can't read disc? Help me!

[Copy link]

8

Threads

19

Posts

501

Credits

Senior Member

Rank: 4

Credits
501

 Vietnam

Post time: 2020-08-16 07:43:56
| Show all posts |Read mode
    I have a D-5 discman, it powers on but doesn't play. I checked and found that the voltage regulator IC was shorted, pin 3 has 9v instead of 5. I replaced the new S81250 and now have 5v at pin 3.
Continuing to check the DC-DC converter, all pins have enough power to play (-5.2, 5.2, GND, 5, 2.3, 9.9) and no voltage drop.
But when you press play, the disc rotates for a few seconds and then turns off? Check if the sled motor moves and emits red light, the Spin motor rotates.
Please help me, where do I have to check again to solve this problem? Thank you very much!


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x
Reply

Use magic Report

4

Threads

22

Posts

125

Credits

Member

Rank: 2

Credits
125

 Greece

Post time: 2020-08-17 13:12:36 From the mobile phone
| Show all posts
Hello, I have no experience with this model, but this unit is very old so replace all the capacitors if you haven't already. Also: open the lid, hold down the open switch and press play (without a disc) to see if the lens move up and down. Hope this helps, good luck!  
Reply Support Not support

Use magic Report

365

Threads

611

Posts

3778

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
3778

 Invalid IP Address

Post time: 2020-08-17 21:30:22
| Show all posts
The motherboard at left side area of the D50 (LCD side) has 4 wires soldered. 2 wires are lid switch; the other 2 are laser switch. You can short the laser switch and test again. The laser switch might be bad contact. Further, you should check whether the laser gear has broken tooth which prevent the movement of the laser.
Reply Support Not support

Use magic Report

8

Threads

19

Posts

501

Credits

Senior Member

Rank: 4

Credits
501

 Unknown

 Author| Post time: 2020-08-17 22:41:26 From the mobile phone
| Show all posts
I don't short-circuit the laser switch because I measure when the door is closed, the laser switch is good! Besides, when I press play, I hear laser screeching, but focus and tracking cannot be found. I will check the laser gear for broken teeth
Reply Support Not support

Use magic Report

8

Threads

19

Posts

501

Credits

Senior Member

Rank: 4

Credits
501

 Unknown

 Author| Post time: 2020-08-19 23:14:04 From the mobile phone
| Show all posts
Edited by nhatminh2007 at 2020-08-20 01:28

I checked the gear and it was normal, the teeth were new and intact. It was quite interesting when I contacted the old owner, it was already playing half the song and stopped. Sometimes it reverse rotates when pressed play. So where do I continue testing?
Reply Support Not support

Use magic Report

365

Threads

611

Posts

3778

Credits

Administrator

Rank: 9Rank: 9Rank: 9

Credits
3778

 Invalid IP Address

Post time: 2020-09-08 09:02:14
| Show all posts
Reverse spinning the disc means TB unbalancing. You can adjust the TB a little bit to see whether it's any better. Be sure to make the pot before adjusting.
Reply Support Not support

Use magic Report

You have to log in before you can reply Login | Repair!

Points Rules

Archive|Mobile|Dark room|Kaosun's CD players

2020-09-21 12:32 GMT-6 , Processed in 0.017002 sec., 14 queries .

Powered by Discuz! X3.2

Release 20141225, © 2001-2020 Comsenz Inc.

MultiLingual version, Rev. 441, © 2009-2020 netdepviet.org

Quick Reply To Top Return to the list